Showing posts with label transistor. Show all posts
Showing posts with label transistor. Show all posts

02 October, 2007

Improved 3 Transistor Audio Amp (80 milliwatt)

This circuit is similar to the one above but uses positive feedback to get a little more amplitude to the speaker. I copied it from a small 5 transistor radio that uses a 25 ohm speaker. In the circuit above, the load resistor for the driver transistor is tied directly to the + supply. This has a disadvantage in that as the output moves positive, the drop across the 470 ohm resistor decreases which reduces the base current to the top NPN transistor. Thus the output cannot move all the way to the + supply because there wouldn't be any voltage across the 470 resistor and no base current to the NPN transistor.

This circuit corrects the problem somewhat and allows a larger voltage swing and probably more output power, but I don't know how much without doing a lot of testing. The output still won't move more than a couple volts using small transistors since the peak current won't be more than 100mA or so into a 25 ohm load. But it's an improvement over the other circuit above.

In this circuit, the 1K load resistor is tied to the speaker so that as the output moves negative, the voltage on the 1K resistor is reduced, which aids in turning off the top NPN transistor. When the output moves positive, the charge on the 470uF capacitor aids in turning on the top NPN transistor.

The original circuit in the radio used a 300 ohm resistor where the 2 diodes are shown but I changed the resistor to 2 diodes so the amp would operate on lower voltages with less distortion. The transistors shown 2n3053 and 2n2905 are just parts I used for the other circuit above and could be smaller types. Most any small transistors can be used, but they should be capable of 100mA or more current. A 2N3904 or 2N3906 are probably a little small, but would work at low volume.

The 2 diodes generate a fairly constant bias voltage as the battery drains and reduces crossover distortion. But you should take care to insure the idle current is around 10 to 20 milliamps with no signal and the output transistors do not get hot under load.

The circuit should work with a regular 8 ohm speaker, but the output power may be somewhat less. To optimize the operation, select a resistor where the 100K is shown to set the output voltage at 1/2 the supply voltage (4.5 volts). This resistor might be anything from 50K to 700K depending on the gain of the transistor used where the 3904 is shown.

3 Transistor Audio Amp (50 milliwatt)

Here is a little audio amplifier similar to what you might find in a small transistor radio. The input stage is biased so that the supply voltage is divided equally across the two complimentary output transistors which are slightly biased in conduction by the diodes between the bases. A 3.3 ohm resistor is used in series with the emitters of the output transistors to stabilize the bias current so it doesn't change much with temperature or with different transistors and diodes. As the bias current increases, the voltage between the emitter and base decreases, thus reducing the conduction. Input impedance is about 500 ohms and voltage gain is about 5 with an 8 ohm speaker attached. The voltage swing on the speaker is about 2 volts without distorting and power output is in the 50 milliwatt range. A higher supply voltage and the addition of heat sinks to the output transistors would provide more power. Circuit draws about 30 milliamps from a 9 volt supply.

Simple Two-Transistor Radio

Here is a simple radio that was designed to minimize unusual parts; there isn't even a detector diode! The sensitivity isn't as high as the one-transistor reflex but the simplicity is attractive. Strong stations will provide plenty of volume into a crystal earphone or an external amplifier. The AM Loopstick was purchased on eBay but the enterprising experimenter can swipe one from the interior of a cheap radio. If the loopstick has more than one winding, use the one with the most turns. Wind 3 or 4 turns near one end of the winding as seen in the photo. The tuning capacitor in the prototype is from an old radio and the little plastic dial was cut down such that it just fit into the back of a black pointer knob. The fit was tight so no glue was needed. All of the sections of the capacitor were connected in parallel to get the most capacitance for this loopstick.

All the other parts are common. The transistors can be just about any small-signal type. The prototype uses the metal can 2N2222, primarily for looks. Some transistors may have too much high frequency gain; if the circuit squeals, try adding a small resistor in the emitter of the first transistor, maybe 47 ohms, the smaller the better as long as the circuit is stable. The large 47 uF could be smaller in most cases but the circuit can pick up hum if the wires are too long. Don't leave out the large capacitor across the battery, it provides needed low power supply impedance.



The circuit is built on a piece of 3.8" x 2.7" x 0.5" stained and varnished oak. The terminals are copper-plated nails used for weatherstripping. These nails are commonly available in home improvement stores and are also available in brass which is also solderable. Predrill the holes to make nailing easier and use a nail set or larger nail turned upside-down to make it easier to hit only the desired nail. The loopstick is held in position by an ordinary nylon cable clamp and the battery is mounted in a spring holder. The front panel is aluminum that was polished to a nice shine. First sand off all scratches with fine sandpaper. Then remove the sanding marks with ordinary kitchen steel wool. Now polish the surface with the finest steel wool in the paint department, usually "000". Then, for the real shine, polish the surface with a polishing compound like rouge. By the way, those paper-wrapped sticks of polishing compound are easily dissolved by lighter fluid (naphtha). Just put a few drops on a tissue and rub it on the end of the stick to load the tissue with compound. These polishing steps go quickly and you can have a mirror finish in a couple of minutes.



The front panel has a couple of scales for the tuning and volume printed on high gloss report cover stock and sprayed with a protective clear spray. The feet on the bottom are recessed in the oak using a forstner bit. The corners on the aluminum and oak were rounded on a belt sander.

Crystal Radio RF Amplifier

One of the best places to add a transistor to a simple crystal radio is at the front end in the form of an RF amplifier. The circuit below is a simple but effective amplifier which will give surprising performance improvement. This amplifier can exhibit negative resistance for low settings of the 500 ohm pot which results in extra gain or even oscillation. So, the circuit can actually be considered to be a regenerative receiver with an external detector. The sensitivity is so high that no cold water pipe ground is needed and the antenna is short.



The behavior of the amplifier depends on how it is connected to the tuned circuit. When connected to a lower impedance tap as shown in the schematic, the gain will be lower with less tendency to oscillate. Higher taps or even connection directly to the antenna will give higher gain and even oscillation. The 500 ohm pot is adjusted to give adequate gain without squealing as stations are tuned. High regeneration settings will actually narrow the bandwidth of the tank enough to give the sound a "mellow" quality which sounds pretty good in a "tinny" crystal earphone! Lower settings are best when using an audio amplifier and the fidelity is quite good thanks to the linear detector (typical regens use changes in the operating point of the transistor to demodulate the RF). As with any regen, the gain may be increased after the station is tuned in and the circuit will oscillate, locked to the station's frequency.
bullet Current consumption is about 1 mA which may be reduced by increasing the 1.8k but the RF envelope begins to distort below about 500 uA.
bullet A 4.5 volt battery may be used if the 220 k resistor is reduced to 68 k.
bullet The transistor may be just about any NPN small-signal transistor.
bullet No ground is shown but performance is better with a good ground connected to the bottom of the tuner.
bullet Longer antennas should be connected to taps instead of across the whole coil. A ferrite loopstick will pick up stronger stations with no antenna at all but use more audio gain after the diode detector and reduce the regeneration to get adequate bandwidth or the sound will be muffled.

One Transistor Amplifier/Detector

An amplifier may be added to boost the audio level as shown below. The current consumption of this amplifier is quite low and a power switch is not included. Disconnect the battery when the receiver is stored for long periods.



Note: You may use the transistor above as a sensitive detector eliminating the need for the 1N34A diode. Simply leave out the diode, the 0.001 uF, and the 82k resistor. Connect the negative side of the 1 uF directly to the coil. Change the base resistor from 10 meg. to 1 meg. and change the collector resistor from 100k to 10k. Now add a 0.01 uF from the collector to the emitter and the modifications are complete. This detector is quite sensitive and will be overloaded by very long antennas! Use a shorter antenna or a coil tap very near ground if significant distortion is noticed. The circuit draws about 1/2 mA.